| 48 Pairs Patch Panel with Module |
• CAT 3 UTP 25-port patch panel.
• Termination: 110 IDC.
• Available with T568A/B wiring pattern and meeting the requirement of CAT 3 standard.
• Design to mount to any standard 19" rack or cabinet.
• Meet or exceed the requirement of ANSI/TIA/EIA 568B.2.
• IDC contact material: phosphor bronze with tin/silver/gold plating over nickel.
• Contact material: phosphor bronze with 6 to 50 U" gold plating over nickel.
• Panel frame: Black or Ivory electrostatic powder-coated steel.
• Fitting for 22/24/26 AWG solid wires.
• Inserting duration: ≥ 750 times.
• Punching duration: ≥ 250 times.
• Insulation Resistance: 500M-ohm.
• Dielectric withstand voltage: 1000V AC RMS, 60Hz 1min.
• Housing material: ABS or PC, UL94-V0 or UL94-V2.
Features and benefits
1. Type: 100 pair rack mount 110 wiring block
2. Available with legs or without legs to the wiring base
3. Easy to adjust, easy to embed wires in
4. Wiring blocks are designed to support voice and high-speed data Application
5. Offering a reliable and economical high-density system
6. The terminal blocks accommodate 22-26 AWG with an insulation diameter of 0.4-0.64mm
7. IDC contract material: phosphor bronze with tin plating over nickel
8. Available with T568A.T568B wiring pattern
| 48 Pairs Patch Panel with Module |
• CAT 3 UTP 25-port patch panel.
• Termination: 110 IDC.
• Available with T568A/B wiring pattern and meeting the requirement of CAT 3 standard.
• Design to mount to any standard 19" rack or cabinet.
• Meet or exceed the requirement of ANSI/TIA/EIA 568B.2.
• IDC contact material: phosphor bronze with tin/silver/gold plating over nickel.
• Contact material: phosphor bronze with 6 to 50 U" gold plating over nickel.
• Panel frame: Black or Ivory electrostatic powder-coated steel.
• Fitting for 22/24/26 AWG solid wires.
• Inserting duration: ≥ 750 times.
• Punching duration: ≥ 250 times.
• Insulation Resistance: 500M-ohm.
• Dielectric withstand voltage: 1000V AC RMS, 60Hz 1min.
• Housing material: ABS or PC, UL94-V0 or UL94-V2.
Features and benefits
1. Type: 100 pair rack mount 110 wiring block
2. Available with legs or without legs to the wiring base
3. Easy to adjust, easy to embed wires in
4. Wiring blocks are designed to support voice and high-speed data Application
5. Offering a reliable and economical high-density system
6. The terminal blocks accommodate 22-26 AWG with an insulation diameter of 0.4-0.64mm
7. IDC contract material: phosphor bronze with tin plating over nickel
8. Available with T568A.T568B wiring pattern
"Non-burning, nicotine for users, low tar content. As the heating temperature (below 500℃) is lower than the combustion temperature of traditional cigarettes (600-900℃), the harmful components produced by tobacco high-temperature combustion pyrolysis and thermal synthesis are reduced, and the release amount of side-flow smoke and environmental smoke (second-hand smoke) is also greatly reduced."
Heating non - combustion products are electronic devices containing tobacco. When you heat them, they produce a nicotine-containing vapor that you can inhale.
They are different from traditional cigarettes and work by heating tobacco to a very low temperature. Tobacco is heated to 350 ° C in a heat-incombustible device, while traditional cigarettes burn at up to 900 ° C.
Still, the temperature at which non-combustion products are heated is high enough to vaporize and inhale harmful chemicals.
Although both are electronic devices, heated non-combustible products are also different from e-cigarettes or steam devices. These usually use chemical liquids and do not necessarily contain nicotine. E-cigarettes tend to heat liquids to around 250 degrees Celsius to produce vapor.
Hnb Device Oem,Hnb Device Patent,Hnb Device,Hnb Device For Sale
Shenzhen MASON VAP Technology Co., Ltd. , https://www.e-cigarettefactory.com